![how to install transmission temp gauge how to install transmission temp gauge](https://i.ebayimg.com/images/g/-dcAAOSwFLBaf4A2/s-l400.jpg)
- #How to install transmission temp gauge drivers
- #How to install transmission temp gauge Bluetooth
- #How to install transmission temp gauge free
Now, when re-installing the ICC, there are two things I had to do. Here is where I put it through the firewall: Then connect these two together.Īnd that’s all you need for the wiring! I then connected the hose for the boost gauge to the blow off valve. Then strip your illumination wires for each of the gauges, twist them together, and crimp a female spade terminal to the end. On the other end of your wire, just crimp a male spade terminal. Then, using a quick splice connector (such as this), use a small length (say 200mm) of wire to splice into it. Just unclip the whole thing (switches and plastic housing) by inserting a screwdriver on the left hand side of it, and prying outwards. To do this, I just tapped into the illumination wire located behind the traction control and fog light switch, to the left of the steering wheel. Next, you will need to connect the illumination wire.
#How to install transmission temp gauge free
Once you have connected your plug into the hands free socket behind the fuse box, then reattach the fuse box by just reversing the instructions. This is the socket we want to be plugging into, the blue one: Then the remove each of the 5 plugs that are attached to the back of the fuse box, as well as unclipping the white OBDII connector.Īnd finally, you can unclip the boot release as well. Then unscrew each of the 3 bolts shown below. To remove the fuse box, disconnect the brown plug. There is only one plug that will fit behind there, so you can’t plug it into anything incorrectly. Now I removed the fuse box, to give you a better idea of what is behind it, but you can fairly easily connect it without removing it, and just by feeling it instead. Once you’ve done that, remove the fuse box cover that’s located to the right under the steering wheel. Then, insert each lug into the respective spot shown in the diagram below (note, the bottom right is not used, it was originally intended to mute the audio for phone calls): Then using a lug crimper, crimp each one to their own male spade lug. twist the each of the power wires together, each of the gorund, etc.). What you’ll need to do is get the power, ground and ignition wire from each gauge, strip the wires, and twist them together (i.e. Then just pull them through until you have just enough wire above the ICC to plug the gauges in.
#How to install transmission temp gauge drivers
Now you’ll need to get the wiring that came with your gauges, and feed the cable down the drivers side behind the dash, until you can see them coming through the foot well. You might be able to do this without removing the ICC, and by just feeding the cables down, but I had no luck. Then, you’ll need to remove the ICC, which you can find instruction on here. Now to remove the top of the ICC, you’ll just need to stick a credit card at the back of it, and pry it upwards and out, it should just clip off as you pry it. I also wired the illumination up to the traction control and fog light switch.įirst things first, when working with anything electrical in the car, it’s always wise to disconnect the battery. If you do however have a hands-free kit using it, you could splice into the wires, otherwise maybe find another source for your wiring. I bought mine from Jaycar Electronics, cat code: PP2066. To do this though, you will need to purchase a 4 pin auto plug to connect your wiring to.
#How to install transmission temp gauge Bluetooth
It was originally intended to be used for bluetooth hands-free car kits, but as I have none, it was trivial to just use that. The easiest and least intrusive way I found to wire my gauges up was to connect them to the plug that lies behind the fuse box located in the cabin. What you purchase is up to you, but to install them is all going to be different, except for the wiring of the ground, power, ignition and illumination (which I’ll show you here) I also purchased a vacuum/boost gauge (This was mainly the one I wanted) as well as a voltage gauge (This was originally purchased just as an easy to install substitute to fill the second pod, but has worked out well as I’m installing the carputer) I purchased a double gauge holder, similar to the ones that were included in the FPV range. You will need to purchase a mount for the gauges (You can get single, double and even triple mounts for the BA-BF falcons that go above the ICC) as well as the gauges to put in them.
![how to install transmission temp gauge how to install transmission temp gauge](https://images.etrailer.com/static/images/pics/D/1/D13009_250.jpg)
I was asked how I had wired up my gauges in my XR6 when I realised I couldn’t find anywhere that specifically showed you, so I thought I would do a write up on it!Īs I had done this quite a while ago, I can’t remember where I purchased my items from, but you can get them at most auto shops, or from online stores and ebay!